Low cost design methods to enhance resolution and dimensions for printed electrodes

Authors

Abstract

In the paper, we demonstrate the feasibility of fabrication interdigitated electrodes with the usage of inkjet printing technology. The emphasis was put to obtain better shape quality and lower spacing between electrodes with respect to the typical printing process. The paper presents an analysis of the main factors that have an influence on the dimension and quality of printed structures and proposes methods that allow eliminating the main problems. The first proposed method is based on controlling the time between patterning successive drops. While the second method is based on changing the design methods and printing orientation. Both methods do not require any additional technological processes or the use of any special surface preparation methods. Finally, the obtained results and conclusions were presented and discussed.

References

C. J. Dias and R. Igreja, “A method of recursive images to obtain the potential, the electric field and capacitance in multi-layer interdigitated electrode (IDE) sensors,” Sensors Actuators, A Phys., 2017.

A. H. Assen, O. Yassine, O. Shekhah, M. Eddaoudi, and K. N. Salama, “MOFs for the Sensitive Detection of Ammonia: Deployment of fcu-MOF Thin Films as Effective Chemical Capacitive Sensors,” ACS Sensors, 2017.

G. Niarchos et al., “Paper-based Humidity Sensor Coated with ZnO Nanoparticles: The Influence of ZnO,” in Procedia Engineering, 2016.

J. Weremczuk, G. Tarapata, and R. S. Jachowicz, “The ink-jet printing humidity sorption sensor - Modelling, design, technology and characterization,” Meas. Sci. Technol., 2012.

H. F. Hawari et al., “Highly selective molecular imprinted polymer (MIP) based sensor array using interdigitated electrode (IDE) platform for detection of mango ripeness,” Sensors Actuators, B Chem., vol. 187, pp. 434–444, 2013.

J. Weremczuk, G. Tarapata, and R. Jachowicz, “Humidity sensor printed on textile with use of ink-jet Technology,” Procedia Eng., vol. 47, pp. 1366–1369, 2012.

T. Mano et al., “Printed Organic Transistor-Based Enzyme Sensor for Continuous Glucose Monitoring in Wearable Healthcare Applications,” ChemElectroChem, 2018.

D. H. Lee, K. T. Lim, E. K. Park, J. M. Kim, and Y. S. Kim, “Optimized ink-jet printing condition for stable and reproducible performance of organic thin film transistor,” Microelectron. Eng., 2013.

G. H. Kim, H. S. Kim, H. S. Shin, B. Du Ahn, K. H. Kim, and H. J. Kim, “Inkjet-printed InGaZnO thin film transistor,” Thin Solid Films, vol. 517, no. 14, pp. 4007–4010, 2009.

M. Kim, J. Dugundji, and B. L. Wardle, “Effect of electrode configurations on piezoelectric vibration energy harvesting performance,” Smart Mater. Struct., 2015.

C. Wang, Z. Wang, T. Ren, and L. Liu, “Design and simulation of a novel operation mode of integrated ferroelectric micro-sensors,” Integr. Ferroelectr., 2006.

H. Sirringhaus et al., “High-resolution inkjet printing of all-polymer transistor circuits.,” Science, vol. 290, no. 5499, pp. 2123–6, Dec. 2000.

L. Zhang et al., “Inkjet printing high-resolution, large-area graphene patterns by coffee-ring lithography,” Adv. Mater., 2012.

M. Caironi, E. Gili, T. Sakanoue, X. Cheng, and H. Sirringhaus, “High yield, single droplet electrode arrays for nanoscale printed electronics,” ACS Nano, 2010.

X. Cao, F. Wu, C. Lau, Y. Liu, Q. Liu, and C. Zhou, “Top-Contact Self-Aligned Printing for High-Performance Carbon Nanotube Thin-Film Transistors with Sub-Micron Channel Length,” ACS Nano, 2017.

Y. Y. Noh, N. Zhao, M. Caironi, and H. Sirringhaus, “Downscaling of self-aligned, all-printed polymer thin-film transistors,” Nat. Nanotechnol., 2007.

W. J. Jasper and N. Anand, “A generalized variational approach for predicting contact angles of sessile nano-droplets on both flat and curved surfaces,” J. Mol. Liq., vol. 281, pp. 196–203, 2019.

W. J. Jasper and S. Rasipuram, “Relationship between contact angle and contact line radius for micro to atto [10− 6 to 10− 18] liter size oil droplets,” J. Mol. Liq., vol. 248, pp. 920–926, 2017.

D.-J. Lin et al., “Rebound Dynamics of Two Droplets Successively Impacting an Inclined Surface,” Coatings, vol. 10, no. 6, p. 592, 2020.

P. Kant, A. L. Hazel, M. Dowling, A. B. Thompson, and A. Juel, “Sequential deposition of microdroplets on patterned surfaces,” Soft Matter, vol. 14, no. 43, pp. 8709–8716, 2018.

D. Soltman and V. Subramanian, “Inkjet-printed line morphologies and temperature control of the coffee ring effect,” Langmuir, vol. 24, no. 5, pp. 2224–2231, 2008.

G. Tarapata and M. Marzęcki, “Methodology and technological aspects of the flexible substrate preparation for ink-jet printing technology,” in Photonics Applications in Astronomy, Communications, Industry, and High-Energy Physics Experiments 2013, 2013, vol. 8903, p. 89032M.

Downloads

Published

2024-04-19

Issue

Section

Technologies and Materials